Smart Water Leak Sensor

MS400H

• Works with Apple HomeKit and compatible with SmartThings.
• Voice Access: Know the status of device via HomePod / Siri.
• Alert: Your Meross app or Apple Home app will receive an alert instantly when leakage is detected.
• Sound Alarm: Up to about 60dB when alarming.
• Low Power Consumption: Up to 18 months lifespan with the built-in battery.
• Automation: Set triggers to control other Meross devices in the Meross app.
• IP67 Waterproof.
• Control Up to 16 Devices: One hub is able to control 16 meross devices (sensors, detectors, thermostat valves) at same time.

SPECS

Battery

CR123A Battery, replaceable

Alarm Volume

About 60 dB (A) at 1m (3ft).

Sensor Dimensions (Dia × H)

φ71.5 × 41.5 mm (φ2.81 × 1.63 in.)

Hub Dimensions (W × D × H)

59 × 41 × 21 mm (2.3 × 1.6 × 0.8 in.)

Wireless Standard

802.11 b/g/n 2.4GHz Wi-Fi (smart hub)

Wireless Standard

433MHz (between smart hub and alarm)

Package Contents

1 × Smart Sensor
1 × Conductor
1 × User Manual
1 × Power Adapter
1 × USB Cable
1 × Smart Hub

System Requirements

Smart phone running iOS 13 or later, Android 6.0 or later
Existing Wi-Fi network

Certifications

US: FCC
EU: CE, RoHS, WEEE

Environment

Operating Temperature: 0°C~40°C (32°F~104°F)
Storage Temperature: -20°C~50°C (-4°F~-58°F)
Operating Humidity: 10%~90% non-condensing
Storage Humidity: 5%~90% non-condensing

FAQS

○

How do I pair the Hub with the Smart Water Leak Sensor?

Double click on the Hub and see the green LED flashing which indicates that the Hub is in pairing mode.
Use the conductor for quick connection of contacts "1 & 2" or contacts "1 & 3" and repeat 3 times in 2 seconds to start pairing with the Hub (within 2 minutes). The snesor LED will flash quickly when pairing.

○

Why is the sensor LED not blinking when I follow the instructions to connect the contacts "1 & 2" or "1 & 3" with wires?

Improper contact between the probe of the wire and the sensor short contact time will lead to the failure and the LED will not blink. In this case, you can wet your fingers and touch the contact point "1 & 2" or "1 & 3" 3 times (within 2 seconds) with your fingers instead of the wire to make the sensor into pairing moede and the LED will blink.
If you have been using it for a long time, the battery might be dead. Please replace the battery and follow the instructions above.

○

What is the sensitivity of Smart Water Leak Sensor to detect water leakage?

When there is water flowing through the sensor (on contact 1&2 or 1&3) for more than 3 seconds, the sensor will determine the leakage.

○

How long can MS400 be used?

Under normal circumstances, sensor will be in low power mode and the battery can last for 18 months. If the power is depleted, you can replace it with a CR123A battery.

○

I see that Meross has several products (sub-devices) that use the Hub, can these products (sub-devices) share one Hub?

Yes, you can. Specifically, the following.
If you are using the HomeKit version of the Hub (the Hub has a Setup Code with an 8 as a number), this Hub supports all sub-devices in the Meross app (which needs to be updated to the latest firmware). All sub-devices except MTS100 and MS100 can be used with this Hub for HomeKit functionality.
If you are using the Non-HomeKit version of the Hub (no Setup Code on the Hub), this Hub only supports MTS100, MS100 2 products in the Meross app and does not support HomeKit functionality.

○

How many devices does a Meross Smart Hub support?

A Meross Smart Hub can support up to 16 devices.

Learn More

DOWNLOAD

Manual

MS400-US-User Manual